Computing Tips

When you get your case you need to check that you got all the bits. Open the case. Now that the case is open,

now is a good time to go through the screw supply provided with the case. These are usually held in a small plastic bag nestled inside the case. Inside this bag you should find:

• Chassis screws – this is the type used to tighten down cards, etc.
• Smaller screws – just like the chassis screws, just with a smaller diameter. It is used to fasten the motherboard in.
• Standoffs – these are screws that are used to hold the motherboard about 1/8″ from the motherboard mounting plate. Their ends have a threaded opening in them that accept the smaller chassis screws. If you have an AT case, you may find small white standoffs. These serve the same function as the metal standoff, but are simply punched through the board and slid into slots on the case. They are rather clumsy to use compared to the metal standoffs, but they get the job done. Lastly, some cases use small metal clip-looking stand-offs. They are pinched together and slipped into small rectangular holes in the motherboard mounting plate and they snap in. These are, too, a bit awkward.
• Washers. These are typically small, loose washers, not the metal kind you’ve seen in your toolbox. These will be used to cushion your motherboard from the screws you will be using to hold it in. Some motherboards have metal plates around the holes to keep the screws from shorting the circuitry, and in this case, washers are not necessary and may not be included.

Check a few things if they need to be done.

1. Clean Case – If the case is new, this should be no big deal. But, if the case has been used before, it could probably stand a cleaning. Clean out the inside with a rag or compressed air. Make sure the fan in the power supply is free of furry dust. Also take a rag and wipe it off.
2. Inspect the Power Supply – Make sure it is tightly attached to the case, make sure it is free of dust, and make sure it is set to the proper voltage of your area- 110V for U.S. and 220V (I think) for outside countries.
3. Inspect Power Switch – Make sure the power switch is securely tightened and correctly connected to the power supply. With most AT cases, the power switch is already connected to the power supply by four wires. In ATX cases, the power switch will have one loose wire coming off of it. This wire will then connect to the Power Switch connector on the motherboard. The power supply should be attached to the power switch already and the connectors should be covered with electrical tape.
4. Install Feet – These are little tabs inserted into holes at the bottom of the case. The case sits on these tabs when on your desk. If the case has been used before or it is a more expensive case, this may not need to be done.
5. Install Case Fan – Sometimes, you may want to install a separate fan that screws onto a rack next to the vent on the front of the case. This helps increase circulation of air through the system. Make sure the fan is set to draw air into the case, not blow out. Many cases already have this installed, so you may not need to worry about it. Some like to put a little filter over the hole so as to prevent dust from being drawn in.
6. Configure the LED – The LED on the case operates completely separate from the actual speed of the system, so you can set that now. It is done with jumpers on the back of the LED. You will need the little manual that came with the case to do this right. Many newer cases don’t even have LED’s, so don’t worry about it.
7. Free Up the Drive Bays – Brand new (cheaper) cases sometimes have the drive bays sealed with metal plates. It’s the most annoying thing. If you want to install any drives, and you probably do, you’ll need to remove these. Choose the drive bays you want to use (usually the ones at the top on tower cases) and remove the metal plates. These are attached by metal, so they take some cutting, prying and twisting to break them free. Be careful not to hurt the case or yourself. The plate will likely have sharp edges once removed. Better cases have these bays covered with plastic, replaceable plates which are a lot easier and make infinitely more sense.

Different Computer Cases Forms There are many different types / forms of computer cases and they are all used for a different job.  The different computer cases are listed below.

Standard Case