How To Install A Processor

How To Install A Processor : All ways be very careful when handling the processor.

Always make sure you ground your self before touching the processor and motherboard. If you give the processor / motherboard a static shock you could break them. There are a few different types of processors. I am going to show you how to install a Pentium 4 processor. 

Just below is a picture of a motherboard. The processor slot is located at the top centre inside where the orange square is.

All processors will only go into the slot one way, So make sure you know what way it goes in. Look at the pins on the processor and then line them up and slot the processor to the motherboard. It will be obvious which way it goes in.

Read More,,

How To Configure A Motherboard

Before you connect your motherboard to your case you need configure your motherboard for the processor/Memory/IO connectors.

If we configure and install these components now it will be much easier than installing them after you have connected the motherboard to the case, You will have more room to work with now.

 

  WARNING, make sure you have grounded your body before touching the computer components. A static shock to a component could damage that component.

 

  Have your motherboard manual ready. You will need this to find the location of certain parts on your motherboard.  Lets start with the processor.  For processor you will need to set 3 things on your motherboard before installing the processor. You will need to look at the manual for your motherboard as you will need to make a few changes. Most motherboards are jumper less and all configuring is done automatically, But incase its not look in the motherboards manual for the following settings,,

 

1 – The Bus Speed. This is the speed in which the processor runs. The faster the bus speed the faster the processor will run. Always set the bus speed to the same as the processor. The processor will run on faster bus speeds (Known as over clocking) But the processor will run at a higher temperature and over heat and eventually stop working.

 

Read More,,

How To Install Windows XP PRO

How To perform a new install of Windows XP PRO

1. Insert your XP CD in the drive. It should automatically launch the Setup routine. If it doesn’t, click Start -> Run, type d:\setup.exe (where d: is the letter of your CD drive) in the Open box and click OK.
2. You’ll be presented with a menu of choices. Click Install Windows.
3. The first setup screen asks you what type of installation to perform. Select New Installation (Advanced) from the drop-down list and click the Next button to move to the next screen.
4. Read More,,

How To Install Windows XP Home

HowTo perform a new install of Windows XP Home

1. Insert your XP CD in the drive. It should automatically launch the Setup routine. If it doesn’t, click Start -> Run, type d:\setup.exe (where d: is the letter of your CD drive) in the Open box and click OK.
2. You’ll be presented with a menu of choices. Click Install Windows.
3. The first setup screen asks you what type of installation to perform. Select New Installation (Advanced) from the drop-down list and click the Next button to move to the next screen.
4. Read through the licence agreement and, if you accept it, click I Accept This Agreement, then click Next.  Read More,,

How To Install Windows 2000

• 
  

  Learn how to install windows 2000 standard edition

  .

  1) Make sure CD-Rom is first Boot Device in your Bios

  2) Insert your Windows 2000 CD

  3) Once this is done boot up using CD-Rom Drive.

  ( If your Hard drive is not setup then this is automatic, if not you will see “Hit any Key to Boot From CD-Rom” on the screen, hit any key on keyboard to invoke CD-Rom boot) 

  Read More,,

How To Install Windows NT

In this guide I will show you how to install Windows NT 4.0. Now follow the following steps.

1. Insert your Windows NT 4.0 CD and Disk 1 of your 3 NT Workstation setup disks
2. Once this is done boot up system.

The following “Hardware Configuration” will appear and Windows NT will detect your hardware configuration.     Read More,,

How To Install Windows 98

In this guide I will show you how to install windows 98

• What you will require to do this walkthrough is 

  1. A Windows 98 CD

  2. A Computer

  3. Your Chosen CD-Rom Boot Media

• The Microsoft Windows 98 Install will prepare to run a system check, after you have completed the routine for your CD-Rom boot and running the setup.exe file. Press enter to run the scandisk.

• The “Windows 98 Setup” screen will now appear. Click “Continue” to move on.

• The Setup wizard will now run through.

• Windows 98, Software License Agreement will now appear. Read through it and when finished click on yes if you agree (Continue with setup) or click on No if you disagree (This exits out of setup)

• Windows 98 Setup Wizard will appear, click “next” to continue.   Read More,,

How To Install Windows Me

In this guide I will show you how to install windows me

• What you will require to do this walkthrough is 

  1. A Windows ME CD

  2. A Computer

  3. Your Chosen CD-Rom Boot Media

  4. Your Chosen Method

• The Microsoft Windows ME Install will eventually run Scandisk, let this complete, if you exit windows will not allow you to complete the install of Windows ME.

• The “Welcome to ME Setup” screen will appear after scandisk completes. You are now ready to begin the installation. Click on “Next” to continue.

• The” Windows Millennium Setup Wizard” screen is next. It is where you will install windows into, C:\Windows is the default, you can change this if needed. Click next to continue.

• Now watch as windows prepares the Directory and Copies Files.

• The “Setup Options” window will appear. For most Desktop users select Typical install (Default) for laptop users select Portable. The other two options speak for themselves. Click next to continue.     Read More,,

How To Install Windows 95

In this guide i will show you how to install windows 95

• What you will require to do this walkthrough is 

  1. A Windows 95 CD

  2. A Computer

  3. Your Chosen CD-Rom Boot Media

• The Microsoft Windows 95 Install will prepare to run a system check, after you have completed the routine for your CD-Rom boot and running the setup.exe file. Press enter to run the scandisk.

• The “Windows 95 Setup” screen will now appear. Click “Continue” to move on.

• The Setup wizard will now run through.

• Windows 95, Software License Agreement will now appear. Read through it and when finished click on yes if you agree (Continue with setup) or click on No if you disagree (This exits out of setup)

• Windows 95 Setup Wizard will appear, click “next” to continue.    Read More,,

How To Install Windows 3.11

Well for this I will show you the install for Microsoft Windows 3.1. Now follow the following steps.

1. Install MSDOS first using the 3 install disks.
2. Once this is done boot up using hard drive.
3. Now go to the A: prompt by typing A: and hitting enter
4. Now type Setup

The “Welcome to Setup” screen will now appear. Hit enter to continue.

You will now be prompted for custom or express setup. Just hit enter for Express

Windows will start copying files to the hard drive, let this continue.

You will then be prompted for disk 2, insert disk 2 and hit enter to continue.

Windows will continue to copy files.

Then the screen looking for “Name” and “Company” will appear and the mouse will become active. Fill in your name and company, click on continue when finished.

You will then be asked to verify the information, click on continue

If using a boot disk to install you will get message about copying system files, click cancel to continue.

Now you will be prompted for Disk 3. Insert before clicking on “Continue”

Windows will continue to copy files..   Read More,,

« Previous Page — Next Page »